CREW project - PHY

LOG-a-TEC

admin — Fri, 29 Jun 2012 10:24:26 +0000

LOG-a-TEC is an outdoor experimental facility supporting cognitive radio networking experimentation in ISM and TV bands. The testbed consists of several clusters of wireless sensor nodes located in the municipality of Logatec, Slovenia and at the Jožef Stefan Institute campus. Clusters in the Logatec municipality cover approximately 350.000 m² of public space that includes the city center and an industrial zone.

Example Experiments:

Various experiments can be performed using the LOG-a-TEC infrastructure, for example:

Investigating different RF interference detection techniques, e.g. distributed vs. centralized detection.
Exploring different interference mitigation techniques, such as adaptive power control.

Access information:

LOG-a-TEC is accessible via a web-interface. Experimenters can install pre-defined firmware on one or more sensor nodes, receive status information, download experiment traces, and interact with individual nodes during an experiment. Also custom firmware can be installed but needs to first be approved. Before running an experiment, the GRASS-RaPlaT tool can be used for simulation. The same tool can be used later to visualize the results of an experiment.

Demonstration:

Getting started and user documentation:

Access the complete documentation

Sensing Engine

peter.vanwesemael@imec.be — Tue, 08 Feb 2011 12:23:53 +0000

The imec sensing enigne is a prototype implementation of a sensing engine for mobile communication devices. The prototype consists of two main blocks: an analog RF front-end including analog to digital conversion and a DIgital Front-end For Sensing (DIFFS). For permanent deployment in the w-iLab.t testbed a WARP board is selected as analog RF front-end, covering the 2.4 and 5 GHz ISM bands. An in house developed flexibele SCAlable raDIO (SCALDIO) is also tested in a lab environment, covering an RF input range from 0.1 up to 6 GHz and a channel bandwidth up to 40 MHz.

Access information:

The imec sensing engine is available in the Ghent island CREW (w-iLab.t testbed).

Getting started and user documentation:

Advanced information

LTE/LTE advanced testbed

admin — Wed, 02 Feb 2011 13:24:36 +0000

Dresden’s LTE/LTE+ like testbed was set up in 2008 as part of the Easy-C project (www.easy-c.com).

Example Experiments:

Various kinds of cognitive radio experiments are thinkable.
Example experiment that requires a secondary system: Coexistence of a primary and a secondary system in licensed frequency bands.
Example experiment that requires a spectrum sensing device: Reliable detection of white spaces in an LTE system with typical user traffic.

Access information:

Experiments in the indoor lab require physical access. Outdoor eNB sites can be accessed via Remote Desktop from within our institute's network. For remote sessions from outside the institute's network, VPN certificates have to be prepared. Please contact us directly at . UEs cannot be accessed remotely.

Getting started and user documentation:

Access the complete documentation

IRIS

admin — Wed, 02 Feb 2011 13:19:15 +0000

Iris is a software radio architecture that has been developed by the CTVR , built in C++, it is used for constructing complex radio structures and highly reconfigurable radio networks. Its primary research application is to conduct a wide range of dynamic spectrum access and cognitive radio experiments. It is a GPP-based radio architecture and uses XML documents to describe the radio structure.

Example Experiments:

In this sample experiment we will run a simple radio and then adapt a component and add a controller, with a view to exploring the basic functionality of both. The steps a researcher should follow to complete the experiment are outlined below.
1. Follow the instructions outlined on the Iris wiki to run radio (https://ntrg020.cs.tcd.ie/irisv2/wiki/ExampleExperiments), OFDMFileReadWrite.XML.
2. If this radio is functioning correctly, “radio running” will appear on the command line.
3. To add a controller to the radio, we must first create an event in one of the components to which the controller can subscribe. To do this, open the shaped OFDM modulator and register an event in the constructor function.
4. Once the event is registered we must create a condition that must be satisfied for the event to be activated. To do this, open the “process” function (as this is where all the calculations are carried out) and specify a condition that activates the controller whenever, for example, 100 packets have passed through.
5. Once this has been done the controller can be made. Open the “example” controller; this gives us a template to work with.
6. Within the controller we must do two things, subscribe to the event that has been set up in the component and specify the parameter that we wish to change as well as the value we wish to change it to.
7. To change the parameter, we specify the name of the parameter as well as the component and engine that it is in. These are assigned in the “ProcessEvent” function.
8. The logic that dictates what the parameter is changed to also goes in this function.
9. Recompile all the relevant code, include the controller in the XML file and run the radio as before.
If the radio is running properly, you should see the event being triggered on the command line and the new value of the parameter in question.

Access information:

Before gaining access to the Iris testbed it is essential to familiarise yourself with the Iris software. This is done through the Iris Wiki page. The Wiki gives you full instructions on how to download and install the Iris software onto your own computer as well as instructions on how to get started in using it. Use of the Wiki page requires a user account and password. These can be obtained through emailing either tallonj@tcd.ie or finnda@tcd.ie.

At this stage users will be able to performe experiments using Iris, independent of the Iris testbed, using either the simulated "channel component" or in conjunction with the USRP (1/2/N210 etc.).

Access to the Iris testbed is given out separately from access to the Wiki. This is because access to the Iris testbed is often not necessary if users have USRP hardware of their own available.

However, if remote access to the Iris testbed (after installing and trying out the Iris software) is required, details of how to obtain access to the testbed can be found here.

Demonstration:

Demonstration of a dynamic spectrum access wireless backhaul system in the UHF band

Getting started and user documentation:

Access the complete documentation

w-iLab.t

admin — Mon, 31 Jan 2011 15:48:04 +0000

The iMinds w-iLab.t allows flexible testing of the functionality and performance of wireless networking protocols and systems in a time-effective way. It provides remote access to hardware that can be remotely controlled and reconfigured, automated experiments can be scheduled, and experimental results can be collected, processed and visualised.

Example Experiments:

A wide range of experiments is possible on w-iLab.t. Below, we first list three possible experiments and then list experiments that have been performed on the testbed within the CREW project:

Three representative examples of cognitive networking experiments are as follows.

Interference avoidance in the 2.4 GHz ISM band: activate a subset of nodes (both sensor nodes using 802.15.4 and Wi-Fi nodes. Implement interference avoidance protocols on top of the sensor node and/or Wi-Fi node. Check the impact on the spectrum using the imec sensing engines installed in the testbed.
Distributed via centralized sensing approaches: compare the difference between different sensing algorithms, e.g. installed on sensor nodes
Performance of low-cost sensing modules: find out how accurate RSSI readings collected by sensor nodes are when implementing a certain channel-sampling algorithm on top of these nodes. Compare this with the performance of high-end sensing solutions, based e.g. on USRPs or imec sensing devices located in the same environment.

Experiments performed during some of the Open Calls of the CREW project:

Determine the sensitivity of various Cognitive Radio sensing engines to low level received signals with and without modulation. Watch video here.
Perform radio channel measurements to study the effects of the environment on the received signal. Watch video here.
Perform energy efficiency and delay evaluation of Spectrum Sensing platforms and algorithms. Watch video here.
Demonstrate self-adapting access mechanisms that are able to switch from standard DCF to a TDMA-like access scheme in case of hidden nodes. Watch video here.
Demonstrate the functional architecture of the control channels for the cognitive management of capacity and coverage extensions of the wireless access infrastructures. Watch video here.

Access information:

Experimenters may use (= install firmware, code, software, images,... on one or more nodes, view status, download results,...) the testbed remotely via an OpenVPN connection over the internet. Most interactions are performed via a web interface, although direct connections to devices over SSH is also possible. The testbeds at both locations (Office, Zwijnaarde) are accessible 24/7, with the restriction that Wi-Fi experiments are not allowed at the Office location during office hours. Usage is bound to a negotiable quota in function of the type and amount of infrastructure needed. Please check the basic w-iLab.t tutorial for details on how to get an account.

Demonstration:

General introduction movie to the w-iLab.t
Information is available from the iLab.t documentation website

Getting started and user documentation:

Access the complete documentation